Produktai skirti ir sunkus (5)

Syntech Roadware Syntech Roadware is a high penetration two-component hybrid urethane which, combined with quartz, produces a hard and instant polymer to repair cracks and crevices in concrete floors. Syntech Roadware has a very low viscosity allowing the penetration of the product in depth, even in the narrowest cracks. It has short reaction times, in fact in 10 minutes at 20°C the material polymerizes completely and catalyzes quickly even in environments with temperatures below 0°C. It has good resistance to chemical attack. When combined with quartz powder, Syntech Roadware, forms a highly resistant compound with properties similar to existing concrete but with the flexibility that persists over time. Repair of splits or cracks in concrete, restoration of deteriorated concrete degradation, repair of cracks and pop-out phenomena in concrete. Slightly widen the crack with a circular saw to facilitate the penetration of Syntech Roadware. Before applying the product, vacuum the dust created. The support must be clean and free from dust or dirt. Apply Syntech Roadware directly on the crack or on the degraded area until the gap is completely saturated. Add quartz directly to the crack and repeat the Syntech Roadware application operation. Smooth with a spatula and leave the product to work. With a Syntech Roadware cartridge, an average of 50 linear metres of gap of 5 mm width is repaired. Bi-mix cartridge 600 ml

Forged steel wrecking bar. Hardened extremities. Epoxy painted. lenght:500mm / 600mm / 700mm / 800mm / 1000mm

Sanaxil I - Therm Smoothed mineral coating for interiors and exteriors with potassium silicates with chemical adhesion, anti-condensation, insulation, mould resistant, thanks to the addition of hollow glass spheres. Sanaxil I - Therm due to its mineral nature with chemical adhesion, revolutionizes the concept of adhesion to the support, penetrating deeply into the pores of the wall to then react with its components and form a unique and indissoluble "silicating" whole. With a final appearance similar to civil plaster. The product does not form a film thus avoiding detachment and peeling phenomena, it ensures a permeability to water vapour thanks to its microcrystalline structure of the same porosity as the wall while guaranteeing excellent water repellency. Elasticity and hardness are coupled in maximum degree with a wide choice of colours not alterable over time; characteristics that, combined with the ease and practicality of application, make the product extremely multi-functional, adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. All products in the Sanaxil I – THERM series cannot be attacked by mould. Recommended as a finish in "cladding" insulation systems, as it helps to increase the thermo-acoustic and anti-condensation coefficient. Stone, masonry, concrete and any type of plaster. The Sanaxil I - Therm system can be applied directly on surfaces treated with mineral paints or new surfaces. If there are residues of organic paint on the support (washable, solvent-based paints, etc.), before application it is necessary to remove them by stripping or sandblasting, and also never apply on plaster, under the beating sun, on warm or wet walls. During application, cover areas that are not to be painted such as jambs, doors, windows and floors because silicates attack glass, metals, ceramics, glazes, paint, marble and granite. Adverse climatic conditions can impose the realization of adequate protection during the application and drying phase of the coating. Never mix with other non-mineral based paints. NEW SUPPORTS Apply a coat of Protech Fix AC - Therm fixative diluted from 20 to 50% with water depending on the absorption of the support. OLD SUPPORTS On old supports, remove the old paint by brushing, fill in any holes or imperfections in the wall with a suitable filler, proceed with fixing with Protech Fix AC - Therm impregnating agent diluted 20 to 50% depending on the absorption of the support. The product is ready to use if necessary add a little water and stir slowly. Apply a coating layer with a stainless steel trowel with a thickness equal to that of the granules it contains. Pass again with a cutting spatula to remove any excess material. After light drying, pass over with a plastic trowel with rotary movements to compact, even out and achieve the full plaster effect. On large surfaces, it is recommended to apply the product of the same lot and proceed always wet on wet to avoid signs of resumption. Indicative consumption depending on the different particle sizes of Sanaxil I - Therm available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 22 kg

Ql Nano Lithium Hard A hardening, anti-dust sealant and chemical thickener with lithium silicates for industrial flooring and surfaces in cement conglomerate in general, already cured and compact. Penetrates and seals concrete via chemical reaction, forming a transparent, durable, extremely hard, inorganic, breathable and abrasion-resistant surface. Excellent for concrete floors requiring long term protection against wear, exposure to unfavourable conditions, humidity, dirt build up, alkalinity and efflorescence (salt residue). QL Nano Lithium Hard deeply penetrates the capillary pores of the concrete, reacting chemically with the free lime to form a permanent and insoluble bond with the concrete. It creates a protective surface layer, which is breathable, thick and resistant to abrasion. It provides a stronger finish, which is impenetrable and pleasant from an aesthetic point of view (smooth-polished) capable of resisting dust, stains and wear. It reduces maintenance intervention and cleaning and repair costs. Hardening, sealing, consolidating and dust-proof treatment of industrial floors and screeds in concrete, both old and new, both grey and coloured. The application surfaces should be clean, free of containment, inconsistent and incoherent parts, dust, etc., conveniently saturated with water to reach the "saturated to dry surface" condition. Apply QL Nano Lithium Hard using a sprayer, roller or brush on the existing concrete surfaces. Always check the surfaces of the concrete are suitable and capable of offering the desired results. Before inspecting and approving the desired application, leave the surface to dry perfectly. The application time on the hardened support should be 24 hours at least in the summer time. 4 - 7 days recommended for the rest of the year. NEW CONCRETE SURFACES QL Nano Lithium Hard can be applied on the concrete surfaces when immediately created after the last finish with the trowel. Carefully clean the substrate, eliminating all the foreign materials such as non-stick products, hardeners, oil, dust, construction efflorescence, gypsum wall residue etc. Use an airless sprayer or type HVLP to apply QL Nano Lithium Hard, in such a way to form a regular, even, compact and polished layer, ensuring total saturation of the surface. Apply a quantity of QL Nano Lithium Hard sufficient to keep the surface wet for 20 minutes. Leave the surfaces to dry (generally for 1 or 2 hours). Proceed by applying a hardening agent according to the standard ASTM C 309. EXISTING CONCRETE SURFACES - Carefully clean the substrate, eliminating all the foreign materials such as non-stick products, hardeners, oil, dust, construction efflorescence, gypsum wall residue, etc. Before proceeding, ensure the surface is dry. - Use a low pressure sprayer to apply QL Nano Lithium Hard in such a way to saturate the surface. - Distribute QL Nano Lithium Hard on the surface using an automatic floor washer or a hard brush to facilitate penetration. - Leave the QL Nano Lithium Hard to act for 20-30 minutes. - Keep the surface wet with QL Nano Lithium Hard for 20 - 30 minutes (if necessary, add other product). - Remove the QL Nano Lithium Hard residue with clean water. - Leave the surface to dry. Apply from 0.07 to 0.09 litres of QL Nano Lithium Hard per square metre of surface to be treated. Packaging: 5-liter can UM: €/l

Osmocem MR Mono-component, osmotic cement mortar based on hydraulic binders, modifying resins and superpozzolanic reactive fillers selected aggregates, for the preparation of adhesive mixtures that after curing, create a protective, waterproof, high-efficiency coating. Osmocem MR can be used for coatings, reconstructions and millimetric protections, finishing coats etc., in interventions of conservative restoration, waterproofing reinforced concrete structures, wall coverings, hydraulic works, extended exposed surfaces etc. Waterproofing rigid structures and masonry walls underground, buried or in any case subject to water permeation: lift wells, basements, tanks, pipes, tunnels, garages, bridges, reservoirs, areas containing food, etc. in conditions of positive and negative hydrostatic thrust, provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Osmocem MR and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 14-16% of the weight of the bag. After mixing is completed wait a few minutes before applying. To further improve the performance of the coating, insert a steel reinforcement mesh (wire 2 mm mesh and 5x5 cm) between layers. Approximately 13,50 kg/m² of Osmocem MR for every centimetre of thickness to be implemented (approximately 1350 kg per cubic metre). Packaging: 25 kg bag Unit: €/kg